Mechanical Design Engineer Wanted – Hydraulic 15-Ton Lifting System for Existing Yacht Transport Trailer

via Freelancer ·

Budget / Salary€250–750
TypeFreelance project
LocationRemote
Posted2 hours ago
Hier ist eine gekürzte und prägnante Version auf Englisch, die optimal auf die Plattform passt (deutlich unter 10.000 Zeichen, exakt 7.288 Zeichen inklusive Leerzeichen) und alle Ihre Anforderungen beibehält:

Wanted: Mechanical Design Engineer – Hydraulic 15-Ton Lifting System for Existing Yacht Transport Trailer

1. Project Description
Looking for an experienced mechanical design engineer to develop a practical, economical, and manufacturing-ready hydraulic lifting system for an existing tandem-axle yacht transport trailer (chassis retained).
Language: Written in English to reach international freelancers. Technical info, photos, dimensions, and communication can be in German (German: spoken & written; English: written only).
I need an experienced engineer, not just a CAD draftsman.

2. Basic Technical Data
Max. payload: 15 tonnes

Min. required lifting height: 200 mm

Max. height of lifting beams in fully lowered position: 700 mm above ground

Trailer: Existing tandem-axle trailer with wheels

Materials: S235 steel, or S355 where required

Lifting beams: Standard square hollow sections (SHS). Engineer determines tube dimensions, wall thicknesses, and materials.

3. Lifting System Design
Two longitudinal lifting beams (left and right), each operated by 2 hydraulic cylinders (4 total).

Requirements: Synchronous equal-stroke operation per side; beams must remain parallel to the chassis; left and right beams independently height-adjustable and separately controlled. Reliable sync under uneven loading.

Engineer develops the hydraulic solution for synchronization and independent control.

4. Yacht Storage Stands & Support Dimensions
Stand widths: 2.00 m (support height 800 mm) or 1.80 m (support height 750 mm).

Stand lengths: Standard 3.0 m (min. 2.5 m, max. 4.0 m).

Support points: 4 per stand (2 longitudinal, 2 transverse). Shortest stands (2.5 m) hold up to 6 tonnes.

Stands are occasionally placed on ~80 mm wooden blocks (to be considered for lift height/geometry). Design must cover all stand variants and support interfaces.

5. Operating Conditions & Safety
Private company premises only (no public roads). Yacht transport allowed in raised position (max. transport speed 5 km/h).

Safety: Safe load holding, protection against unintended lowering and hose/line failure. Dynamic transport loads (acceleration, braking, cornering, uneven ground) must be considered. Engineer evaluates necessary safety measures and checks if mechanical locks are required.

6. Hydraulic Power Unit & Electrical Supply
12 V battery-powered HPU mounted on trailer.

Engineer specifies: Motor, pump, tank, operating pressure, flow rate, valves, hoses/pipes, electrical power/peak current, battery voltage/capacity, recommended battery type, and charging system. Includes hydraulic circuit diagram and BOM.

Target: ~60 complete lifting cycles (raise + lower) per charge.

Operation: Interface for radio or wired remote control (allow for both).

Note: I will mount the HPU on the trailer.

7. Engineering Scope & Calculations
Assessment and measurement of existing trailer/space.

Structural calculation of the longitudinal beams of the main chassis only for additional lifting loads.

Design of longitudinal lifting beams (SHS).

Design of cylinder mounts, guides, bearings, pivots, and connections.

Selection and sizing of 4 hydraulic cylinders.

Development of synchronization and independent control.

HPU selection, circuit diagram, and BOM.

Force, geometry, movement, and lifting calculations.

Preliminary strength/stability checks for new structure and chassis longitudinal beams.

Consideration of uneven/eccentric loads, torsion, and transport dynamics.

Welded joint design and battery sizing (~60 cycles).

Complete manufacturing-ready design.

8. Calculation Approach – Practical & Cost-Effective
Practical approach preferred. Extensive FEM reports not required unless technically necessary. Covers chassis longitudinal beams, lifting beams, cylinder forces/stroke, pressure/flow, synchronization, HPU/battery, and main load cases. Assumptions and results must be clearly documented.

9. CAD & Manufacturing Deliverables
Readable on a standard PC without expensive software (PDFs, images):

Complete 3D CAD model integrated with trailer chassis + editable native CAD + STEP files.

Manufacturing drawings (PDF), 3D views, assembly drawings, welding details, BOM.

1:1 DXF files for flame/plasma cutting (clean, closed contours, no duplicates).

Hydraulic circuit diagram, component list, 12 V electrical/battery specs.

10. Existing Information
Photos with handwritten dimensions and reference images provided. Unclear dimensions must be agreed upon beforehand.

11. Required Experience
Hydraulic lifting systems, cylinder synchronisation, heavy-duty/welded structures, vehicle/trailer construction, structural calculations, manufacturing-oriented CAD, 12 V HPUs, and workshop drawings. Heavy transport experience is a plus.

12. Proposal Requirements & Milestones
Include: Intro/background, comparable projects, CAD software used, sync/control approach, recommended HPU/battery, estimated duration, and detailed quotation.

Milestone 1: Technical concept & initial 3D design.

Milestone 2: Completed mechanical design, chassis longitudinal beam & strength calculations, hydraulic design, HPU/battery sizing.

Milestone 3: Manufacturing drawings, DXF files, BOM, and full documentation handover.

13. Important Note
Safety-relevant 15-tonne design. Economical, practical, and manufacturing-ready approach required while fulfilling essential safety standards. Must be reviewed by a qualified professional before commissioning.
3d rendering mechanical engineering illustration autocad 3d modelling mechanical design 2d drafting
Apply on Freelancer →

Project sourced from Freelancer.com. Applications happen directly on the original platform — we never collect your data.