Design a 250 TPH Gold Wash Plant
Budget / Salary$750–1,500
TypeFreelance project
LocationRemote
Posted1 hour ago
Mechanical / Mineral Processing Engineer Needed – Complete 250 TPH Gold Wash Plant Design
PROJECT OVERVIEW
We are seeking an experienced mechanical or mineral processing engineer to design a complete 250-ton-per-hour (TPH) placer gold wash plant utilizing a heavy-duty vibrating shaker deck.
The plant will be fabricated from scratch in Ethiopia using locally available steel and manufacturing capabilities, with specialized mechanical components imported where necessary.
We are looking for an engineer with proven experience designing vibrating screens, aggregate washing plants, mineral processing equipment, or complete gold wash plants.
Our goal is to develop a reliable, efficient, modular wash plant optimized for continuous operation, ease of maintenance, and high gold recovery.
The final design must be independently engineered and suitable for fabrication.
PRELIMINARY PLANT SPECIFICATIONS
Processing capacity: 250 metric tons per hour
Maximum feed rock size: 400 mm (approximately 16 inches)
Material: Alluvial gold-bearing gravel, sand, and rocks with minimal sticky clay
Feeding method: Wheel-loader-fed hopper
Screening system: Heavy-duty vibrating shaker deck with integrated spray bars
Grizzly: Preferably no separate grizzly, subject to engineering evaluation
Screen apertures: Approximately 10–15 mm, subject to optimization
Water requirement: Approximately 3,000 GPM available, with final flow and pressure to be engineered
Gold recovery: Multiple parallel sluice boxes, preliminarily six at approximately 1 m wide × 7 m long
Power: Electric motors supplied by an industrial diesel generator
Operating schedule: Approximately 16 hours per day
Plant configuration: Modular design suitable for disassembly and relocation between mining sites
All preliminary specifications are subject to engineering verification and optimization.
SCOPE OF ENGINEERING WORK
1. COMPLETE PLANT DESIGN
Overall plant configuration and process flow
Loader-fed hopper and material distribution
Vibrating shaker deck and screening system
Spray bars and water distribution
Sluice boxes and gold recovery system
Oversize and tailings discharge
Modular structural supports and assembly connections
2. MECHANICAL AND STRUCTURAL ENGINEERING
Vibrating screen sizing and operating parameters
Exciter, spring, bearing, and motor selection
Dynamic load calculations and vibration isolation
Structural analysis, including fatigue-critical components
Steel frame and support design
Wear-resistant components and replaceable liners
Engineered lifting points and modular connections
The design must account for frequent 400 mm rocks in the feed material.
3. HYDRAULIC AND RECOVERY SYSTEM
Water flow and pressure calculations
Spray-bar and nozzle configuration
Pump and piping specifications
Sluice sizing, slope, and flow distribution
Fine gold recovery optimization
Water collection and discharge arrangements
4. FABRICATION AND ASSEMBLY DOCUMENTATION
We require a complete engineering package suitable for manufacturing by a third-party fabrication workshop.
Deliverables must include:
Complete 3D CAD assembly of the entire wash plant
Detailed 2D fabrication drawings for every manufactured component
Structural and mechanical engineering calculations
Material specifications and steel thicknesses
Welding and bolted-connection details
Complete bill of materials (BOM)
Specifications for purchased components
Steel cutting and fabrication schedules
Modular assembly and installation instructions
Electrical and mechanical equipment specifications
Editable CAD source files (SolidWorks, Inventor, or equivalent)
PDF and DXF manufacturing drawings
REQUIRED EXPERIENCE
Applicants should have experience with at least one of the following:
Heavy-duty industrial vibrating screens
Mineral processing plant design
Aggregate washing and screening equipment
Placer gold wash plants
Mining equipment manufacturing
Structural and dynamic analysis of vibrating machinery
Preference will be given to engineers who can demonstrate equipment they have personally designed that was successfully fabricated and operated.
PROPOSAL REQUIREMENTS
Please include the following information in your bid:
1. Examples of similar equipment or plants you have designed.
2. Your specific experience with vibrating screen engineering.
3. Whether you can provide complete fabrication-ready drawings and engineering calculations.
4. Your proposed project timeline.
5. Your estimated total project cost and recommended payment milestones.
6. The engineering and CAD software you use.
7. Whether you can provide technical support during fabrication and initial commissioning.
PROJECT OBJECTIVE
Our objective is to obtain a complete, independently engineered, manufacturing-ready design that can be fabricated in Ethiopia without purchasing a complete wash plant from an equipment manufacturer.
We are seeking an experienced engineering professional or team capable of taking the project from initial concept through final fabrication documentation.
This is not a CAD drafting or rendering-only project. Engineering calculations, mechanical design expertise, and practical manufacturing experience are essential.
The client must receive editable source files and the necessary rights to fabricate, modify, repair, and reproduce the custom-designed equipment. Any pre-existing or third-party intellectual property must be disclosed.
PROJECT OVERVIEW
We are seeking an experienced mechanical or mineral processing engineer to design a complete 250-ton-per-hour (TPH) placer gold wash plant utilizing a heavy-duty vibrating shaker deck.
The plant will be fabricated from scratch in Ethiopia using locally available steel and manufacturing capabilities, with specialized mechanical components imported where necessary.
We are looking for an engineer with proven experience designing vibrating screens, aggregate washing plants, mineral processing equipment, or complete gold wash plants.
Our goal is to develop a reliable, efficient, modular wash plant optimized for continuous operation, ease of maintenance, and high gold recovery.
The final design must be independently engineered and suitable for fabrication.
PRELIMINARY PLANT SPECIFICATIONS
Processing capacity: 250 metric tons per hour
Maximum feed rock size: 400 mm (approximately 16 inches)
Material: Alluvial gold-bearing gravel, sand, and rocks with minimal sticky clay
Feeding method: Wheel-loader-fed hopper
Screening system: Heavy-duty vibrating shaker deck with integrated spray bars
Grizzly: Preferably no separate grizzly, subject to engineering evaluation
Screen apertures: Approximately 10–15 mm, subject to optimization
Water requirement: Approximately 3,000 GPM available, with final flow and pressure to be engineered
Gold recovery: Multiple parallel sluice boxes, preliminarily six at approximately 1 m wide × 7 m long
Power: Electric motors supplied by an industrial diesel generator
Operating schedule: Approximately 16 hours per day
Plant configuration: Modular design suitable for disassembly and relocation between mining sites
All preliminary specifications are subject to engineering verification and optimization.
SCOPE OF ENGINEERING WORK
1. COMPLETE PLANT DESIGN
Overall plant configuration and process flow
Loader-fed hopper and material distribution
Vibrating shaker deck and screening system
Spray bars and water distribution
Sluice boxes and gold recovery system
Oversize and tailings discharge
Modular structural supports and assembly connections
2. MECHANICAL AND STRUCTURAL ENGINEERING
Vibrating screen sizing and operating parameters
Exciter, spring, bearing, and motor selection
Dynamic load calculations and vibration isolation
Structural analysis, including fatigue-critical components
Steel frame and support design
Wear-resistant components and replaceable liners
Engineered lifting points and modular connections
The design must account for frequent 400 mm rocks in the feed material.
3. HYDRAULIC AND RECOVERY SYSTEM
Water flow and pressure calculations
Spray-bar and nozzle configuration
Pump and piping specifications
Sluice sizing, slope, and flow distribution
Fine gold recovery optimization
Water collection and discharge arrangements
4. FABRICATION AND ASSEMBLY DOCUMENTATION
We require a complete engineering package suitable for manufacturing by a third-party fabrication workshop.
Deliverables must include:
Complete 3D CAD assembly of the entire wash plant
Detailed 2D fabrication drawings for every manufactured component
Structural and mechanical engineering calculations
Material specifications and steel thicknesses
Welding and bolted-connection details
Complete bill of materials (BOM)
Specifications for purchased components
Steel cutting and fabrication schedules
Modular assembly and installation instructions
Electrical and mechanical equipment specifications
Editable CAD source files (SolidWorks, Inventor, or equivalent)
PDF and DXF manufacturing drawings
REQUIRED EXPERIENCE
Applicants should have experience with at least one of the following:
Heavy-duty industrial vibrating screens
Mineral processing plant design
Aggregate washing and screening equipment
Placer gold wash plants
Mining equipment manufacturing
Structural and dynamic analysis of vibrating machinery
Preference will be given to engineers who can demonstrate equipment they have personally designed that was successfully fabricated and operated.
PROPOSAL REQUIREMENTS
Please include the following information in your bid:
1. Examples of similar equipment or plants you have designed.
2. Your specific experience with vibrating screen engineering.
3. Whether you can provide complete fabrication-ready drawings and engineering calculations.
4. Your proposed project timeline.
5. Your estimated total project cost and recommended payment milestones.
6. The engineering and CAD software you use.
7. Whether you can provide technical support during fabrication and initial commissioning.
PROJECT OBJECTIVE
Our objective is to obtain a complete, independently engineered, manufacturing-ready design that can be fabricated in Ethiopia without purchasing a complete wash plant from an equipment manufacturer.
We are seeking an experienced engineering professional or team capable of taking the project from initial concept through final fabrication documentation.
This is not a CAD drafting or rendering-only project. Engineering calculations, mechanical design expertise, and practical manufacturing experience are essential.
The client must receive editable source files and the necessary rights to fabricate, modify, repair, and reproduce the custom-designed equipment. Any pre-existing or third-party intellectual property must be disclosed.
Apply on Freelancer →
Project sourced from Freelancer.com. Applications happen directly on the original platform — we never collect your data.